Available for App 2.3.8
Step 1: Map Creation and Navigation
1.Click "Start-Start mapping" or"Lawn"on the home page. The application will guide you through the necessary checks (Wi-Fi, GPS, Bluetooth, mobile phone battery, and Novabot battery levels). Then click the Map button
2.Try dragging the green circle in the middle toward the arrows to steer the robot to the edge of the lawn. (The start button turns green means the location is right to map, click it to proceed to the next step.)
The Done button turns green means the map is created, click it to proceed to the next step
Reset means remapping from the beginning
Retract means the mower will backtrack automatically and you can click stop to stay in the ideal position and remapping
(Reset and retract options are also available when creating the obstacles and channels)
Note
1.Returning to the charging station is only necessary when the first map is created.
2.Only three maps can be created and they must be connected to each other by a channel.(
The number of the maps are being increased)
3.The channel will be forced to build when the first map is created, provided that the distance between the lawn and the charging station is greater than 1.5m and the mower is not directly facing the charging station.
4.Do not place two maps too close together, as the mower may mistake it for a passageway and attempt to go straight through.
5.After creating two maps, the Map icon will become inactive. To create a new map, first create the obstacle or channel and then return to create the map again.
6.Remapping is necessary if GNSS antenna or base is moved after mapping
New Function
Note
1.Advanced settings can only be accessed online and will take effect the next time a new job is started.
2.My device-Manual controller no need to carry the mower back to base
3.Do not activate the Manual Controller while the mower is charging to avoid receiving notifications constantly (being improved)
4.Speaker and Headlight are being improved
5.Select the angle for mowing and preview it to check. (Path direction)
6. Low(Detection）Medium and High(Segmentation) Being improved (Obstacle avoidance sensitivity)
7.Max speed: Adjusting the speed of the mower's travel; Handling:Adjusting the speed of the mower when turning corners.
8. From left to right, they are battery, RTK, bluetooth and wifi. The status of the items is indicated by their colour. Cyan indicates good condition, red indicates bad condition, and grey indicates offline.
Step 2 Obstacle and Channel creation (Finish means exit the current interface)
1.Click 'Obstacle' to create the map of no go area (Move your Novabot to the map you created if the start button doesn't turn to green)
The Done button turns green means the map of no go area is created, click it to proceed to the next step
Note
1. Mower can avoid obstacles on its own (Being improved)
2.To ensure the mower works properly, remove any weeds, branches, or obstacles longer than 20cm. (being improved)
3.It is possible to create obstacles after creating 2 maps
2.Channel creation
Click 'Channel' to create the passageway between two maps (Move your Novabot to the map you created if the start button doesn't turn to green)
The Done button turns green means the channel is created, click it to proceed to the next step
Note
1.The channel length must be longer than 0.5 meters and within the RTK range. otherwise the channel cannot be used even though it can also be created
New Function
After creating three maps, click 'Finish' to proceed to the next step. The notification will then appear automatically.
Step 3 Mowing
There are three ways to trigger mowing.
1.Start
Note
1.When mowing the grass, you have two options when clicking 'back': (A) terminate or (B) pause. Terminate means to reset, starting from the beginning. Pause means to stop at a moment, allowing you to know which areas have been mowed and which have not.
2.Lawn
Note
1. The map appears when you click the start button and appears at the mowing time you have set in the schedule. (The button in grey means the mower is working)
2.The inflated boundaries are calculated by the system according to the map created, which helps the mower to record the mowing path.
3.Cut grass along the edges.The mower will continue mowing the area surrounding the Red circle (no-go area that you created) and the corners of the entire map at least three times, even if it appears that the mower has already mowed the entire map in the app. (The process on the homepage can also be proven) and the color will be darker than the surrounding area.
4.The edit button can be used to change the name of the map.
5.Light green indicates the area to be mowed and dark green indicates the mowed area; A solid line changes to a dotted line indicates the second mowing and will start from the beginning. A dotted line will appear when mowed once.
6.Due to the inflated boundaries (spacing interval between the no go area and the map that need to mow or the different lines), the mower may not move from the location indicated on the map.
7.It repairs itself when the mower is stopped (RTK is lost) during mowing.
8.The mower can continue from the last stopping point when pressing the back button. (being improved)
9.Lawn-Add/Edit-Modify map It can remap the boundary of the map and start mowing again.
3.Schedule
Note
1.The mower will automatically start working once the schedule is created (The schedule will become invalid if the start button is triggered after it has been created).
2.Unlimited creation
3.Show the current date
4.The time can be changed directly and will not go back to 8:00 for further changes.
5.If the schedule you created disappeared due to an error, select 'retry' in the 'Date' option in advance.(Being improved)
6.The shortest amount of time for a schedule is 30 minutes.
Note: The article will be updated every Thursday as needed. Feel free to leave a comment if you have any questions or suggestions. We will do our best to improve it.
Comments
0 comments
Please sign in to leave a comment.